What A92.20 Actually Requires
The regulatory language is brief. An active load-sensing device is required on all A92.20 MEWPs. Machines must actively monitor load and interrupt normal operations by sounding an alarm if overloaded. An operator cannot begin a job with an overloaded machine.
For scissor lifts specifically, the behavioral consequence of an overload condition is more defined. JLG's description of its production system states that an overload results in disabling of all vehicle motion until the excessive platform weight is cleared. This includes drive, steer, and further elevation. The system sounds an alarm sequence and illuminates indicator lamps at both platform and ground controls.
The critical design nuance is that descending must remain possible. JLG's system, for example, allows operators to descend from an overload condition even though further elevation and drive are disabled. This is not an optional convenience. If the load-sensing system traps an operator at height with no way to lower the platform, it has created a new hazard in the process of addressing an overload condition. The A92.20 design intent is to prevent operation under overload, not to strand the operator.
A second nuance: the rated capacity is not a single number in all cases. Some scissor lifts have different indoor and outdoor ratings. The load-sensing system must determine which rating applies based on the machine's configuration or operating mode, and compare the measured load against the correct threshold. A system calibrated only for indoor capacity will either allow outdoor overload or trigger nuisance alarms on legitimate outdoor loads.
The Pressure-Based Architecture: Why It Dominates and Where It Fails
For scissor lifts, the dominant load-sensing approach uses hydraulic pressure as the measured variable. The logic is physically grounded: the lift cylinder supports the platform load, and the pressure required to hold or move that load is proportional to the force applied. A pressure transducer on the cylinder, combined with a measurement of platform height (from a rotary sensor on a pivot point or a tilt sensor on a scissor arm), allows the controller to infer platform load.
This architecture has practical advantages. It does not require load cells or sensing pins in the platform structure, which are exposed to damage and contamination. It uses the hydraulic system that already exists. And it can be calibrated against known weights.
But pressure-based sensing has a specific failure mode that OEMs must design around: hydraulic fluid viscosity changes with temperature. A system calibrated at 20°C will produce different pressure readings at 0°C for the same load. JLG addresses this by using pressure transducers on both the rod side and the head side of the lift cylinder, allowing the controller to compensate for viscosity effects in low temperatures. A manufacturer that fits a single pressure sensor and calibrates only at ambient shop temperature will produce machines that either trigger nuisance overload alarms in cold conditions or fail to detect genuine overload when the fluid is warm.
The height measurement subsystem introduces a second dependency. Pressure alone cannot distinguish between an empty platform at full height and a loaded platform at partial height, because the cylinder force varies with geometry. The controller needs both pressure and height to resolve load. If the height sensor drifts or fails, the load calculation becomes invalid. The A92.20-compliant design must therefore include diagnostics that detect height sensor failure and place the machine in a safe state-not simply continue calculating load from a bad height input.
Calibration: The Hidden Engineering and Service Burden
A load-sensing system is only as accurate as its calibration. The calibration process establishes the relationship between measured pressure, measured height, and known load. Without a valid calibration, the system cannot determine whether a given pressure-height combination corresponds to an overload condition.
The calibration procedure for a production scissor lift is not a trivial field adjustment. Genie's published calibration procedure for its GS models requires the platform to be fully raised and lowered multiple times with known test weights in the platform, with the controller gathering data at each stage. The procedure must be performed on a firm, level surface free of overhead obstructions, and for indoor-rated models, either indoors with sufficient ceiling height or outdoors under specified wind conditions. The calibration generates a dynamic pressure curve that the system uses to determine overload conditions in service.
This creates two design obligations for the OEM. First, the calibration must be repeatable. If the same machine calibrated twice under the same conditions produces materially different curves, the system will not behave consistently. This depends on the stability of the pressure sensing, the height sensing, and the hydraulic system itself. Second, the calibration must be verifiable. JLG has implemented a "Load Verification" function that runs a single empty lift cycle and compares the data against the stored calibration. If the machine characteristics have drifted beyond limits, the system flags the need for recalibration. This allows fleet operators to screen machines quickly without loading test weights onto every unit.
For a manufacturer entering the North American market, the service infrastructure implication is significant. A load-sensing system that requires full test-weight calibration after every sensor replacement or major hydraulic service creates a service burden that rental fleets will resist. Systems that support empty-deck calibration with a diagnostic tool, without platform weights, reduce that burden-but the OEM must validate that the empty-deck calibration produces a curve that remains accurate across the machine's operating envelope.
Failure Modes and the "Fail-Safe" Question
The most consequential design decision for a load-sensing system is what happens when a component fails. A92.20 does not prescribe a specific failure response, but the design intent is clear: a failed sensing system must not allow the machine to operate in an unsafe condition.
Consider the possible failures:
Pressure sensor failure. If the transducer fails open or shorted, the controller may read zero pressure or full-scale pressure. A zero reading could be interpreted as an empty platform, allowing operation under a genuine overload. A full-scale reading could trigger a permanent nuisance alarm. The controller must be able to detect sensor failure-through signal plausibility checks, redundant sensing, or diagnostic circuits-and place the machine in a defined state. JLG's dual-transducer approach provides a degree of cross-checking between rod-side and head-side readings, but the diagnostic logic that compares them is the actual safety mechanism.
Height sensor failure. A drifting or failed height signal invalidates the load calculation. The system should detect implausible height transitions (e.g., a sudden jump from 2 meters to 8 meters without corresponding pressure change) and inhibit operation. Genie's calibration procedure explicitly requires confirming that the platform height sensor is not damaged and functions correctly before calibration begins, which implies that height sensor integrity is a known dependency for the load system.
Controller failure. If the lift controller itself fails, the load-sensing function is lost. The machine's overall safety architecture must ensure that a controller failure results in a stopped machine, not an uncontrolled one. This is a system-level requirement that extends beyond the load-sensing subsystem.
The design principle that emerges from these failure modes is that load sensing must be self-diagnostic. A system that cannot tell the operator (and the service technician) that it has failed is not a safety system; it is a source of silent risk. The A92.20 requirement for an active system that "interrupts normal operations" presumes that the system is functioning. If it has failed silently and the machine continues to operate, the requirement is not met.
Integration with Machine Control and the Operator Experience
A load-sensing system that meets the standard but degrades the operator experience will be circumvented, ignored, or complained about until the fleet manager disables it. The OEM's design challenge is to make the system informative rather than obstructive within the bounds of the standard.
The standard requires that normal operation be interrupted on overload. It does not require that the interruption be opaque. The system should tell the operator what is wrong (overload), where the indication is visible (platform and ground controls), and what action resolves the condition (remove weight). JLG's system uses an alarm sequence and indicator lamps at both control stations. The operator knows why the machine stopped and what to do about it.
The nuance around descent is critical. If the machine is overloaded at height, the operator needs to come down. A system that disables descent along with drive and lift creates a rescue scenario out of a manageable situation. The design must distinguish between "do not allow further elevation or travel" and "do not allow the platform to be lowered." The former is required by the standard; the latter is a design defect.
A second operator-experience consideration is nuisance activation. Scissor lifts experience dynamic loads during travel over rough surfaces, sudden stops, and wind gusts. A load-sensing system with insufficient filtering or an overly tight threshold will trigger on these transient conditions. The operator will experience the machine stopping unexpectedly on a jobsite, conclude that the system is unreliable, and lose confidence in it. The calibration and signal-processing design must tolerate normal dynamic loads while still detecting genuine static overload.
What OEMs Must Deliver Beyond the Sensor
The A92.20 load-sensing requirement is often described as a sensor requirement. That framing is misleading. The sensor is a component. The compliance artifact is a system: sensor(s), height measurement, controller logic, calibration procedure, diagnostic capability, alarm and indication, and integration with the machine's motion control and emergency descent functions.
For a manufacturer designing for the North American market, the minimum deliverables are:
A documented calibration procedure that specifies the conditions, the test weights, the sequence, and the acceptance criteria. The procedure must be repeatable in a service environment, not only in a factory.
A diagnostic strategy that detects sensor failures, signal implausibility, and calibration drift, and that places the machine in a defined safe state when these conditions occur.
A service calibration path that does not require full test weights for every sensor replacement, or the fleet operator will defer maintenance and the system will drift out of calibration.
Validation evidence that the system performs across the machine's operating temperature range, height range, and load distribution. A system calibrated and tested only at mid-height with a centered load is not validated for a platform extension with a concentrated load.
Operator-facing documentation that explains what the overload indication means, what actions are permitted and prohibited, and how to resolve the condition without creating a new hazard.
The manufacturers that treat load sensing as a checkbox-fit a pressure sensor, write a calibration routine, ship the machine-will produce equipment that passes a static audit but fails in the field. The ones that treat it as a control-system design problem will produce machines that operators trust and fleets can maintain.
Summary
ANSI A92.20 load sensing is a design requirement, not a component requirement. The standard mandates an active system that monitors load and interrupts operation on overload, but it does not specify the architecture, the failure behavior, or the calibration method. Those decisions belong to the OEM, and they determine whether the system is a genuine safety function or a liability.
For scissor lifts, the pressure-based approach is the industry norm for good reasons: it uses existing hydraulic infrastructure and avoids platform-mounted sensors exposed to damage. But pressure sensing requires temperature compensation, reliable height measurement, and a calibration process that can be executed and verified in service. The system must detect its own failures and fail in a way that protects the operator rather than stranding them at height. And it must be informative enough that operators do not treat it as an obstacle to be worked around.
The manufacturers that will succeed in the North American market are those that can deliver not just a compliant machine, but a maintainable, diagnosable, and trustworthy load-sensing system-one that fleet managers can calibrate without excessive downtime and that operators can understand without a service call.






